TOYOTA MR2 / CELICA

The Racer X Fabrication center feed intake manifold for the 1991-1995 Toyota MR2 / Celica is a perfect addition to any build!! Increases in horsepower and torque will vary to each build but average gains are 40 whp and 30 ft/lbs torque. The center feed intake manifold is perfect for the side mount intercooler and allows for almost OEM packaging. Construction The Racer X Fabrication center feed intake manifold's gains can be attributed to our plenum that is designed to eliminate the flow issues...

The Racer X Fabrication straight runner intake manifold for the 1991-1995 Toyota MR2 is a perfect addition to any build!! Increases in horsepower and torque will vary to each build but average gains are 40 whp and 30 ft/lbs torque. This intake manifold is housed in the trunk of the MR2 and has the best efficiency due to the runners being almost perfectly straight. The design also allows the plenum to be isolated from the HOT engine bay and reduces intake temperatures. The straight runner...

The Racer X Fabrication shifter cable bushing spacers for the 91-95 Toyota MR2 are specifically designed to allow a greater amount of articulation not found in the standard kit using flat washers. The bushing spacers also eliminate the small amount of movement between the spacers and cotter pin. These changes lead to an improved shifting feedback and reduces binding in the cables which is often described by enthusiasts as a notchy shifter. The spacers are CNC machined from 6061-T6 aluminum to...

The Racer X Fabrication side feed intake manifold for the 1991-1995 Toyota MR2 / Celica is a perfect addition to any build!! Increases in horsepower and torque will vary with each build but average gains are 40 whp and 30 ft/lbs torque. The side feed intake manifold is perfect for air to water intercooler setups or trunk mount intercoolers, but can also be used with the side mount intercooler. Construction The Racer X Fabrication side feed intake manifold's gains can be attributed to a...

Tired of looking at your worn out oil cap! The Racer X Fabrication oil cap for the Toyota MR2 and Toyota Celica will clean things up and look great!! CNC machined right here at Racer X Fabrication from 6061-T6 aluminum and uses a viton o-ring for a perfect seal. What's Included (1) Oil Cap Compatibility 1991-1995 Toyota MR2 Toyota MR2 Gen 2 Toyota MR2 Gen 3 Toyota MR2 Gen 4 Installation Install Time: 1 min Installation Guide Proposition 65 WARNING: Cancer and Reproductive Harm...

The Racer X Fabrication Bosch fuel pressure regulator adapter is designed to be used with the popular Bosch fuel pressure regulators. The bosch 3 bar and 4 bar regulators are often used on many of today's modern fuel systems in OEM applications. The Racer X adapter allows the use of the Bosch 3 bar and 4 bar regulator to be directly adapted to any 3/4-16 RH threaded fuel rail or -8AN ORB. The adapter is threaded for a -8AN ORB for the return line and comes with a -6AN to 8AN ORB fitting. The...

The Racer X Fabrication transmission linkage bushings for the 1991-1995 Toyota MR2 are a direct OEM replacement for the worn out polymer bushings found in the OEM shifter linkage assembly. After 30 years of use, the OEM bushings are almost completely worn out which leads to a sloppy or disconnected feeling during shifting. The Racer X linkage bushings are designed specifically for the E153 transmission and CNC machined from oil impregnated bronze. The bronze bushings provide crisp, direct feed...

What's Included (2) Urethane bushing (2) Retaining washer Compatibility 1991-1995 Toyota MR2 Toyota MR2 Gen 2 Toyota MR2 Gen 3 Toyota MR2 Gen 4 Installation Install Time: 15 to 30 mins Installation Guide--> Proposition 65 WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov Off Road Use Only WARNING: Racer X Fabrication products are intended for off-road / competition use only and may never be used on a public road. ...

The Racer X Fabrication distributor cover for the 91-95 Toyota MR2 is perfect for those that have eliminated the need for the OEM distributor cap and are now using a crank trigger for your ignition timing. The aluminum cover simple bolts on to the OEM distributor just like the OEM cap. What's Included (1) Aluminum distributor cover Compatibility 1991-1995 Toyota MR2 Installation Install Time: 15 min Installation Guide--> Proposition 65 WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.go...

The Racer X Fabrication coolant tree for the Toyota MR2 was designed as a replacement for the OEM coolant tree that is often corroded from years of use. The coolant tree features 8AN ORB fittings and includes the hose barbs, which can also be blocked off with 8AN plugs should you choose to eliminate the heater lines. Finally the assembly retains the OEM coolant temperature sensor and the gauge sensor. It will eliminate the OEM cold start injector switch and VSV. Construction The Racer X...

The Racer X Fabrication Cam trigger kit for the 1991-1995 Toyota MR2 provides the final component for those that are still using the OEM distributor and an external crank trigger wheel. The cam trigger kit eliminates the OEM distributor completely, and allows your EMS to run full sequential ignition and fuel. Construction The Racer X Fabrication cam trigger wheel utilizes a CNC machined adapter that keys to the intake cam of the 3SGTE engine. The cam wheel rotates from the keyed adapter...

The Racer X Fabrication 1ZZ crank trigger kit for the 1991-1995 Toyota MR2 is the best ignition solution for high performance 3SGTE engines. The crank trigger kit will eliminate high RPM ignition drift, which can be as much as 5 to 10 degrees above 6000 RPM. This kit will allow you to run optimal timing without worry about your timing belt stretching and giving erratic readings to the OEM distributor. The 1ZZ coils also eliminate the need to change your spark plug wires, distributor cap and...

The Racer X Fabrication 1zz valve cover adapter plate for the 91-95 Toyota MR2 allows you to easily adapt the 1zz coils to the Gen 2 and Gen 3 valve cover. The adapter plate comes with the hardware needed to complete the installation. *Note: If you are using the OEM intake manifold the coil adapter plate will require modification on coil #3 to clear the throttle body inlet. What's Included (1) 1ZZ valve cover adapter plate Compatibility 1991-1995 Toyota MR2 (Gen 2, Gen 3, Gen 4) Installation...

The Racer X Fabrication BPV block off for the 1991-1995 Toyota MR2 was designed to eliminate the OEM BPV valve. The block off can assist in maintaining boost pressure between shifts and improve spool response. The block off plate is CNC machined from 6061-T6 aluminum and includes a new o-ring seal to replace the old OEM rubber seal. The BPV block off comes in a raw finish and the Racer X logo is CNC etched into the face of the plate. What's Included (1) BPV block off (1) O-ring seal (1)...

The Racer X Fabrication BSPT oil pressure sensor adapter for the 1991-1995 Toyota MR2 / Celica was designed to eliminate the various fittings and adapters needed to use an aftermarket gauge. The OEM cylinder head for the 3SGTE is threaded using an 1/8" BSPT, which can cause several issues when trying to retain the OEM oil pressure sensor and add an aftermarket pressure gauge. The Racer X Fabrication BSPT adapter conveniently allows you to add an aftermarket gauge and keep the OEM oil pressure...