Products 49-60 of 60
Show
Availability: In Stock
Item #: 010013 -
Tired of looking at your worn out oil cap! The Racer X Fabrication oil cap for the Toyota MR2 and Toyota Celica will clean things up and look great!! CNC machined right here at Racer X Fabrication from 6061-T6 aluminum and uses a viton o-ring for a perfect seal. What's Included (1) Oil Cap Compatibility 1991-1995 Toyota MR2 Toyota MR2 Gen 2 Toyota MR2 Gen 3 Toyota MR2 Gen 4 Installation Install Time: 1 min Installation Guide Proposition 65 WARNING: Cancer and Reproductive Harm...
Availability: In Stock
Item #: 010006 -
The Racer X Fabrication press in AN fitting for the 1991-1995 Toyota MR2 is designed to remove the OEM PCV fittings and replace them with hose end fittings. The fitting is CNC machined to be a press fit into the Gen 2, Gen 3, and Gen 4 OEM valve cover. The AN fittings make it simple and easy to covert the OEM rubber lines to braided hose and AN hose ends. Please be sure to select the correct fitting for the Gen 3 and Gen 4 applications as the PCV and Crankcase fittings are different sizes....
Availability: In Stock
Item #: 011002 -
The Racer X Fabrication BSPT oil pressure sensor adapter for the 1991-1995 Toyota MR2 / Celica was designed to eliminate the various fittings and adapters needed to use an aftermarket gauge. The OEM cylinder head for the 3SGTE is threaded using an 1/8" BSPT, which can cause several issues when trying to retain the OEM oil pressure sensor and add an aftermarket pressure gauge. The Racer X Fabrication BSPT adapter conveniently allows you to add an aftermarket gauge and keep the OEM oil pressure...
Availability: In Stock
Item #: 011001 -
The Racer X Fabrication oil level block off plate for the 1991-1995 Toyota MR2 eliminates the OEM oil level sensor. The OEM oil level sensor is often removed by enthusiasts and replaced with sheet metal plates. Enter the Racer X oil level block off, the block off plate is CNC machined from 6061-T6 aluminum and includes a new o-ring seal. The block off plate works on the OEM MR2 oil pan or the Moroso oil pan. What's Included (1) Racer X oil level block off plate (1) O-ring (4) M6x1 SS button...
Availability: Out of Stock
Item #: 010001 -
The Racer X Fabrication mustang throttle body conversion for the 1991-1995 Toyota MR2 is a simple way to convert an 86-93 Mustang 5.0 throttle body to Toyota MR2 electronics. The mustang throttle body is a popular upgrade for many MR2 enthusiasts but leaves a little bit of a headache when attempting to use the OEM TPS, and ISC. The Racer X adapter plates for the Toyota TPS and ISC allow you to directly bolt these components onto a mustang throttle body. The finished assembly allows you to plug...
Availability: Out of Stock
Item #: 010015 -
The Racer X Fabrication side window vents for the 1991-1995 Toyota MR2 were designed to replace the OEM vents that are faded, cracked or broken. The updated design matches the OEM MR2 side air intake vents for common design style and appearance. The vents are cut from 5052 Aluminum and anodized black to be similar to the OEM vent color. What's Included (2) MR2 side window vents (6) Stainless steel screws Compatibility 1991-1995 Toyota MR2 Installation Install Time: 15 to 30 mins Proposition 65...
Availability: In Stock
Item #: 010406 -
The Racer X Fabrication rear subframe inserts for the Toyota MR2 were designed to reduce the diameter between the bolt and subframe. The gap between the 4 bolts and the subframe ranges from 0.04” to 0.187” (1mm-4.75mm). This gap allows the subframe to articulate under loading that happens during acceleration. The Racer X subframe inserts reduce this gap while still allowing the subframe to bolt into the factory position. The inserts increase power transfer and improve feedback during...
Availability: In Stock
Item #: 010007 -
The Racer X Fabrication BPV block off for the 1991-1995 Toyota MR2 was designed to eliminate the OEM BPV valve. The block off can assist in maintaining boost pressure between shifts and improve spool response. The block off plate is CNC machined from 6061-T6 aluminum and includes a new o-ring seal to replace the old OEM rubber seal. The BPV block off comes in a raw finish and the Racer X logo is CNC etched into the face of the plate. What's Included (1) BPV block off (1) O-ring seal (1)...
Availability: In Stock
Item #: 010002 -
The Racer X Fabrication throttle body inlet for the 1991-1995 Toyota MR2 is a direct replacement for the OEM throttle body inlet. The OEM throttle body inlet is smaller than the throttle body opening which creates a small restriction before entering the throttle body. The Racer X throttle body inlet matches the OEM throttle body opening for the Gen 2 and Gen 3 which reduces the airflow restriction through the throttle body. The flange is CNC machined from 6061-T6 aluminum and welded to your...
Availability: In Stock
Item #: 010901 -
Availability: In Stock
The MR2 Midship Runabout vinyl decal is approximately 5" x 5" and is cut from premium 5 year outdoor vinyl. Availble in white, black, silver and red. Made in USA. What's Included (1) MR2 Midship Runabout Decal Compatibility Universal Installation Install Time: 5 min Installation Guide--> Proposition 65 WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov Off Road Use Only WARNING: Racer X Fabrication products are intended for off-road / competition use only and may never be used on a...
Availability: Out of Stock
What's Included (1) MR2 radio bezel trim Compatibility 1991-1995 Toyota MR2 --> Proposition 65 WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov Off Road Use Only WARNING: Racer X Fabrication products are intended for off-road / competition use only and may never be used on a public road. ...