MISC PARTS

What's Included (1) Door panel insert RH (1) Door panel insert LH (1) Mounting template Compatibility 1991-1995 Toyota MR2 Installation Install Time: 15 - 30 mins Difficulty Level: Installation Guide Proposition 65 WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov Off Road Use Only WARNING: Racer X Fabrication products are intended for off-road / competition use only and may never be used on a public road. ...

The Racer X Fabrication shifter surround kit for the 1991-1995 Toyota MR2 is a great addition to any interior. The shifter surround kit completely replaces the OEM shifter surround, shift boot and shift knob (optional). The kit mounts directly to the OEM mounting locations using the supplied fasteners. Our aluminum shift boot retainer is designed to engage the bottom of the shift knob to eliminate that sagging OEM shift boot often found in your MR2. The Racer X Fabrication shifter surround is...

The Racer X Fabrication side window vents for the 1991-1995 Toyota MR2 were designed to replace the OEM vents that are faded, cracked or broken. The updated design matches the OEM MR2 side air intake vents for common design style and appearance. The vents are cut from 5052 Aluminum and anodized black to be similar to the OEM vent color. What's Included (2) MR2 side window vents (6) Stainless steel screws Compatibility 1991-1995 Toyota MR2 Installation Install Time: 15 to 30 mins Proposition 65...

The Racer X Fabrication light weight alternator bracket for the 91-95 Toyota MR2 is a great start to reducing weight and saving space. The OEM alternator bracket takes up a large amount of space on the 3-SGTE engine and weighs a little over 11 lbs. The Racer X light weight alternator bracket kit is CNC machined from 6061-T6 Aluminum and weighs just under 2 lbs fully assembled. The tensioner is made from zinc plated hex steel and uses rod ends to allow adjustment over the full range of worn or...

The Racer X Fabrication battery brace for the Toyota MR2 was designed to replace the OEM brace and increase aesthetic appearance. The Racer X battery brace is CNC machined from 6061-T6 aluminum, and uses the OEM M6 nuts. The brace is anodized black for corrosion resistance and finally laser etched with the Racer X logo. What's Included (1) Racer X battery tie down (1) Tie down adapter (1) M6 stainless steel button head (1) 1/4” washer (1) 1/4”-20 clinching stud (1) 1/4”-20 flange nut...

The Racer X Fabrication engine bay heat shield for the 1991-1995 Toyota MR2 was designed to replace the OEM component. The OEM heat shield is often rusted, broke or just missing a few components. The Racer X heat shield is a one piece design and provides additional clearance around the radiator hard lines by the cabin wall. The shield is lower profile than the OEM unit specifically at the bottom portion by the cabin wall engine mount. The heat shield is cut from 5052 aluminum sheet and formed...

The Racer X Fabrication rear subframe inserts for the Toyota MR2 were designed to reduce the diameter between the bolt and subframe. The gap between the 4 bolts and the subframe ranges from 0.04” to 0.187” (1mm-4.75mm). This gap allows the subframe to articulate under loading that happens during acceleration. The Racer X subframe inserts reduce this gap while still allowing the subframe to bolt into the factory position. The inserts increase power transfer and improve feedback during...

Tired of looking at your worn out oil cap! The Racer X Fabrication oil cap for the Toyota MR2 and Toyota Celica will clean things up and look great!! CNC machined right here at Racer X Fabrication from 6061-T6 aluminum and uses a viton o-ring for a perfect seal. What's Included (1) Oil Cap Compatibility 1991-1995 Toyota MR2 Toyota MR2 Gen 2 Toyota MR2 Gen 3 Toyota MR2 Gen 4 Installation Install Time: 1 min Installation Guide Proposition 65 WARNING: Cancer and Reproductive Harm...

The Racer X Fabrication BSPT oil pressure sensor adapter for the 1991-1995 Toyota MR2 / Celica was designed to eliminate the various fittings and adapters needed to use an aftermarket gauge. The OEM cylinder head for the 3SGTE is threaded using an 1/8" BSPT, which can cause several issues when trying to retain the OEM oil pressure sensor and add an aftermarket pressure gauge. The Racer X Fabrication BSPT adapter conveniently allows you to add an aftermarket gauge and keep the OEM oil pressure...

The Racer X Fabrication oil level block off plate for the 1991-1995 Toyota MR2 eliminates the OEM oil level sensor. The OEM oil level sensor is often removed by enthusiasts and replaced with sheet metal plates. Enter the Racer X oil level block off, the block off plate is CNC machined from 6061-T6 aluminum and includes a new o-ring seal. The block off plate works on the OEM MR2 oil pan or the Moroso oil pan. What's Included (1) Racer X oil level block off plate (1) O-ring (4) M6x1 SS button...

The Racer X Fabrication press in AN fitting for the 1991-1995 Toyota MR2 is designed to remove the OEM PCV fittings and replace them with hose end fittings. The fitting is CNC machined to be a press fit into the Gen 2, Gen 3, and Gen 4 OEM valve cover. The AN fittings make it simple and easy to covert the OEM rubber lines to braided hose and AN hose ends. Please be sure to select the correct fitting for the Gen 3 and Gen 4 applications as the PCV and Crankcase fittings are different sizes....

The Racer X Fabrication fuel pump relay bracket for the 91-95 Toyota MR2 is designed to clean up the engine bay. The bracket allows you to eliminate the OEM fuel injector resistor pack and then mount the fuel pump relay and fuel pump resistor pack onto the Racer X Fabrication bracket. The bracket is CNC laser cut from 6000 series aluminum and is powder coated wrinkle black for corrosion resistance and an OEM appearance. **NOTE** This product will eliminate the OEM injector resistor pack,...

The Racer X Fabrication cam cap for the 1991-1995 Toyota MR2 for the 3SGTE engine was designed as a direct replacement for the OEM cam cap. The OEM cap is typically quite worn and usually the torx bit bolts are stripped making removal difficult. The Racer X cam cap is CNC machined from 6061-T6 aluminum and is cut to the same dimensions as the OEM component. The cap includes new bolts, which are not a common thread size. The replacement is a great way to clean up your engine bay or replacement...

The Racer X Fabrication throttle body inlet for the 1991-1995 Toyota MR2 is a direct replacement for the OEM throttle body inlet. The OEM throttle body inlet is smaller than the throttle body opening which creates a small restriction before entering the throttle body. The Racer X throttle body inlet matches the OEM throttle body opening for the Gen 2 and Gen 3 which reduces the airflow restriction through the throttle body. The flange is CNC machined from 6061-T6 aluminum and welded to your...

The Racer X Fabrication accessory plug was designed to replace the OEM component and increase aesthetic appearance. The Racer X accessory plug is CNC machined from 6061-T6 aluminum. The plug is anodized black for corrosion resistance and finally laser etched with your choice of design. What's Included (1) Racer X accessory Compatibility Universal Installation Install Time: 1 min Installation Guide--> Proposition 65 WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov Off Road Use Only...